在直埋敷設的設計和施工必須真正了解加熱管分為直埋敷設和直埋敷設無擴張，兩種方法都有各自的特點和兩個方法，設計一個合理的選擇和建設直埋保溫管的工作原理的應用是的，可靠的經濟。
In the design and construction of direct buried laying must really understand the heating pipe is divided into direct buried laying and direct buried laying without expansion, both methods have their own characteristics and two methods, design a reasonable choice and construction of the working principle of the direct buried insulation pipe is safe, reliable and economical.
直埋保溫管道敷設有補償：通過自然補償和補償器（如方形補償器和波紋管補償器），將熱應力降更低。直埋敷設沒有補償，這僅僅意味著對管道的熱量沒有補償，而是熱應力吸收。
Direct buried insulation pipe laying has compensation: through natural compensation and compensators (such as square compensators and bellows compensators), the thermal stress is minimized. There is no compensation for direct embedding, which simply means that there is no compensation for the heat in the pipeline, but thermal stress absorption.
直埋直埋保溫管無需補償安裝、安裝，熱管先固定到一定溫度后，再進行固定管焊接，當管道回溫（低溫）時，管道在拉伸應力作用下提前進行。當通過熱管工作時，隨著溫度的升高，管道應力為零，在繼續升溫時，壓縮應力增大，當溫度達到工作溫度時，管道的壓縮應力、熱應力仍小于許用應力。這樣，管道就可以在不補償設備的情況下工作。
There is no need to compensate the installation and installation of the directly buried and directly buried insulation pipe. After the heat pipe is fixed to a certain temperature, the fixed pipe is welded. When the pipe returns to temperature (low temperature), the pipe is carried out in advance under the action of tensile stress. When working through the heat pipe, the pipe stress is zero as the temperature increases. When the temperature continues to rise, the compressive stress increases. When the temperature reaches the working temperature, the compressive stress and thermal stress of the pipe are still less than the allowable stress. In this way, the pipeline can work without compensating the equipment.
第四強度理論中要求預熱管道施工的補償方法，在施工中會非常麻煩，在國內外也有許多工程實踐，理論計算可靠，能保證。近年來，在的北京煤制氣的熱設計院的分類進行了分析，并對第三強度理論的方法和應力的應用。該方法充分發揮了鋼的塑性潛力，施工方便，不預熱。
The fourth strength theory requires the compensation method of preheating pipeline construction, which will be very troublesome in the construction. There are also many engineering practices at home and abroad. The theoretical calculation is reliable and can guarantee the safety. In recent years, the classification of the thermal design institute of coal gasification in Beijing, China has been analyzed and the application of the third strength theory method and stress. The method gives full play to the plastic potential of steel, which is convenient for construction and not preheating.
兩不同埋深的考慮因素：直埋安裝部署，嵌入深度來確定補償，只考慮不會破壞管道的穩定性可能是由于地面荷載，從經濟方面考慮，施工方便，方法等要埋在直埋補償盡可能淺。上覆巖層的厚度應大于0.6米，不論管徑大小。
Two different burial depth considerations: direct burial installation and deployment, embedding depth to determine the compensation, only considering that the stability of the pipeline will not be damaged may be due to the ground load, from the economic perspective, construction convenience, methods to be buried in direct burial compensation as shallow as possible. The thickness of the overlying strata shall be greater than 0.6 m, regardless of pipe diameter.
當直埋無補償，考慮穩定性的管道埋深要求，一般覆土厚度、埋藏深度、穩定性，比有補償直埋敷設時使用無預熱無補償電路，更小覆土深度應規則和城市熱網設計規范（cjj34-90），一次覆土厚度7.2.15個執行，是直徑大小成正比。
When there is no compensation for direct burial, the buried depth of the pipeline considering the stability of the requirements, general soil cover thickness, burial depth, stability, than the use of compensation for direct burial without preheating and compensation circuit, minimum soil cover depth should be rules and urban heat network design code (cjj34-90), the first soil cover thickness 7.2.15 implementation, is proportional to the diameter.
