環氧樹脂防腐鋼管詳細介紹：1，由鋼管：無縫鋼管焊接鋼管螺旋焊管等各類鋼管2環氧樹脂這款產品的涂料是一種雙 - 組分，高固體分涂料由環氧樹脂作為主劑。分底漆和面漆。集團由環氧樹脂，顏料，添加劑和飼料的成分。乙固化劑改性的胺制備。
Epoxy resin anticorrosive steel pipe detailed introduction: 1, by steel pipe: seamless steel pipe welding steel pipe spiral welded pipe and other steel pipe 2. Epoxy resin coating of this product is a two-component, high solid content coating by epoxy resin as the main agent. Divided into primer and topcoat. The group consists of epoxy resins, pigments, additives and feed ingredients. Preparation of amine modified by B curing agent.
二，特性及應用：良好的耐用性，環氧樹脂固化后漆膜堅韌，防水，無毒性，不污染水。附著力強，具有涂層和涂膜之間的非常好的附著性。生銹優異的防水性能，具有優良的防銹材料，可保證防銹性能。隨著機械強度，漆膜堅韌，具有耐磨性和耐沖擊性能。高固含量，涂層厚。室溫固化膜。沒有大的烘烤設備。對飲用水水箱，水管，水箱，水塔供水設備內壁涂料和糖，谷物貨位使用廣泛適用。也可以用來作為一個游泳池，一個發電廠冷卻塔并加載到燃料油，汽油，金屬，混凝土內壁涂料。
2、 Characteristics and application: good durability, the cured epoxy film is tough, waterproof, non-toxic and does not pollute water. Strong adhesion and excellent adhesion between coating and film. Rust excellent waterproof performance, with excellent anti rust materials, can ensure the anti rust performance. With the mechanical strength, the film is tough, with wear resistance and impact resistance. High solid content, thick coating. Room temperature curing film. There is no big baking equipment. It is widely used for drinking water tank, water pipe, water tank, water tower, inner wall coating of water supply equipment, sugar and grain storage. It can also be used as a swimming pool, a cooling tower in a power plant and loaded with fuel oil, gasoline, metal, concrete inner wall coating.
三、技術指標： （注：耐化學試劑為底，面復合層)項目 指標 項目 指標 漆膜外觀及顏色 白色、漆膜平整 抗沖擊力公斤/厘米 50 粘度（涂-4粘度計）秒 >30 附著力（劃圈法）級 1 干燥時間：表干（h） <2 柔韌性（mm） 1 實干（h） 24 耐3%鹽水 72h 無變化 耐10%酸、堿、鹽
3、 Technical indicators: (Note: chemical resistance is the base, surface composite layer) project index project index: the appearance and color of the paint film is white, the paint film is flat, the impact resistance is kg / cm 50 viscosity (coating-4 viscometer) s > 30 adhesion (circle method) level 1 drying time: surface dry (H) < 2 flexibility (mm) 1 dry (H) 24 3% salt water resistance 72 h no change, 10% acid, alkali and salt resistance
四，施工及貯存：（1）應該是畫的灰塵，油污，氧化皮，清潔等。在2.5的水平，以保證涂裝質量前的物體表面。禁止建設水。（2）施工配比方法如下：A組份嘴巴張開，將參加A組B股，充分攪拌均勻。固化30分鐘，就可以進行涂層。（3）與使用的比例的分配材料的要求，該涂層應在8小時內完成。未完成的材料來進行密封。應該在雨天或相對溫度停止施工高于75％。對于腐蝕介質嚴重的部位，建議多道涂刷。（4）本品應存放于陰涼干燥處，避免陽光直接照射，隔絕火源，遠離熱源。的貯存期十二個月，應在期限屆滿后，檢查各項技術指標，如符合指標要求的，可以繼續使用。
4、 Construction and storage: (1) should be painting dust, oil, oxide scale, cleaning, etc. At 2.5 level to ensure painting quality before the surface of the object. Construction of water is prohibited. (2) The construction proportioning method is as follows: the mouth of component A shall be opened, and the B-strand of group A shall be fully mixed. After curing for 30 minutes, the coating can be carried out. (3) The coating shall be completed within 8 hours in proportion to the distribution material requirements used. Unfinished material to seal. The construction should be stopped in rainy days or relative temperature higher than 75%. For the parts with serious corrosive medium, it is recommended to apply multiple coats. (4) This product should be stored in a cool and dry place, avoid direct sunlight, keep away from fire source and heat source. After the expiration of the storage period, the technical indicators should be checked. If the requirements meet the requirements, they can be used again.
The above wonderful content has polyurethane insulation steel pipe manufacturers http://www.qndr49.cn Provide technical support, our website will continue to present a lot of new information for you, please remember to pay attention to us!
