1. In order to prevent the deformation of the cast-iron plate, when hoisting the cast-iron polyurethane insulation pipe platform, four steel wire ropes of the same length should be used to hang the four lifting holes on the cast-iron plate at the same time, and the cast-iron plate should be stably hoisted on the transportation tool.

2、將鑄鐵聚氨酯保溫管平臺支承點墊好、墊平，保證每個支撐點受力均勻，保證整個鑄鐵平板平穩。

2. The supporting points of cast iron polyurethane insulation pipe platform shall be well padded and leveled to ensure that each supporting point is evenly stressed and the whole cast iron plate is stable.

3、鑄鐵聚氨酯保溫管平臺安裝時將鑄鐵平板的各個支撐點用調整墊鐵墊好、墊實，由技術人員將鑄鐵平板調整合格精度。

3. During the installation of cast iron polyurethane insulation pipe platform, each supporting point of cast iron plate shall be padded with adjusting pad iron, which shall be adjusted to qualified precision by professional technicians.

4、鑄鐵聚氨酯保溫管平臺使用時要輕拿輕放工件，不要在鑄鐵平板上挪動比較粗糙的工件，以免對鑄鐵平板工作面造成磕碰、劃傷等損壞。

4. When using the cast-iron polyurethane insulation pipe platform, handle the workpiece gently, and do not move the rough workpiece on the cast-iron plate, so as to avoid damage to the working face of the cast-iron plate such as collision, scratch, etc.

5、為了防止鑄鐵聚氨酯保溫管平臺整體變形，使用完畢后，要將工件從鑄鐵平板上拿下來，避免工件長時間對鑄鐵平板重壓造成鑄鐵平板的變形。

5. In order to prevent the integral deformation of the cast iron polyurethane insulation pipe platform, the workpiece should be removed from the cast iron plate after use, so as to avoid the deformation of the cast iron plate caused by the heavy pressing of the cast iron plate for a long time.

6、鑄鐵聚氨酯保溫管平臺不用時要及時將工作面洗凈，然后涂上一層防銹油，并用防銹紙蓋上，用鑄鐵平板的外包裝將鑄鐵平板蓋好，以防止平時不注意造成對鑄鐵平板工作面的損傷。

6. When the cast iron polyurethane insulation pipe platform is not in use, the working surface shall be cleaned in time, then coated with a layer of antirust oil, covered with antirust paper, and covered with the outer package of the cast iron plate, so as to prevent the damage to the working surface of the cast iron plate caused by carelessness at ordinary times.

7、鑄鐵聚氨酯保溫管平臺應安裝在通風、干燥的環境中，并遠離熱源、有腐蝕的氣體、有腐蝕的液體。

7. Cast iron polyurethane insulation pipe platform shall be installed in a ventilated and dry environment, and away from heat source, corrosive gas and corrosive liquid.

8、鑄鐵聚氨酯保溫管平臺按標準實行定期周檢，檢定周期根據具體情況可為6-12個月。包裝：鐵板包裝和木制包裝兩種形式，平臺表表用塑料膜封裝，這種包裝適于平板內陸運輸，并有良好的防潮、防震、防銹和防野蠻裝卸等保護平板的措施,以確保運抵現場。

8. Cast iron polyurethane insulation pipe platform shall be subject to periodic weekly inspection according to national standards, and the verification period can be 6-12 months according to specific conditions. Packaging: two forms of iron plate packaging and wooden packaging. The surface of the platform is sealed with plastic film. This packaging is suitable for inland transportation of the flat plate, and has good measures to protect the flat plate, such as moisture-proof, shockproof, rust proof and rough handling, so as to ensure safe transportation to the site.

聚氨酯保溫管平臺的運輸：運輸是保證平板不變形的一個重要環節，所以運輸平板時要保證不超載，不超速，不疲勞駕駛， 不在天氣惡劣的情況下運輸。

Transportation of polyurethane insulation pipe platform: transportation is an important link to ensure that the flat plate does not deform, so when transporting the flat plate, it is necessary to ensure that it is not overloaded, overspeed, fatigue driving, or transported in bad weather.

使用注意事項：聚氨酯保溫管平臺在使用時要行安裝調試。然后，把平板的工作面擦拭干凈，在確認沒有問題的情況下使用，使用過程中，要注意避免工件和平板的工作面有過激的碰撞，防止損壞平板的工作面;工件的重量更不可以超過平板的額定載荷，否則會造成工作質量降低，還有可能損壞平板的結構，甚會造成平板變形，使之損壞，無法使用。

Precautions for use: polyurethane insulation pipe platform shall be installed and debugged before use. Then, wipe the working surface of the plate clean, and use it when there is no problem. During the use process, pay attention to avoid excessive collision between the workpiece and the working surface of the plate, and prevent damaging the working surface of the plate; The weight of the work piece shall not exceed the rated load of the flat plate, otherwise, the work quality will be reduced, the structure of the flat plate may be damaged, and even the flat plate will be deformed, so that it can not be used.